A thyratron is a type of gas filled tube used as a high energy electrical switch and controlled rectifier. Triode, tetrode and pentode variations of the thyratron have been manufactured in the past, though most are of the triode design. Because of the gas fill, thyratrons can handle much greater currents than similar hard vacuum valves/tubes since the positive ions carry considerable current. Gases used include mercury vapor, xenon, neon, and (in special high-voltage applications or applications requiring very short switching times) hydrogen.[1] Unlike a vacuum tube, a thyratron cannot be used to amplify signals linearly. Source Wiki.

The movie shows 3 of my thyratrons, while being energized. The 714 (Mercury Vapor and Gas), the 309CE/FG-17 and the 3C31/ELC1B. Here are the datasheets:
The first two contain mercury. If stored or unused for a long period, the mercury can deposit on the internal walls and components. Extra care must be taken when warming such a tube, to avoid short circuits inside it. Also it is a must to first power the filament and then apply the switching voltage .

The thyratron is a gas-filled discharge chamber that contains a cathode filament, an anode plate, and one or more grids. An inert gas or metal vapour fills the discharge chamber. The grid controls only the starting of a current and thus provides a trigger effect. The normal grid potential is negative with respect to the cathode and prevents electrons from flowing to the plate and exciting a discharge. To cause a discharge, the grid potential is raised enough to start electrons flowing from the cathode. As free electrons stream toward the plate, they collide with gas molecules, freeing other electrons and ionizing the gas within the discharge chamber. When a sufficient number of ions and electrons are present, a “short” occurs, and a large current flows from the cathode to the plate, causing a discharge. The discharge can take place in a few hundred-millionths of a second. The discharge stops when the anode voltage has been sufficiently lowered. The grid can be used to initiate a discharge but can't be used to terminate one. After a discharge, a thyratron has a deionization time, needed for the ions to revert back to the neutral state. While ionized the Thyratron is conductive, so it will trigger even without a grid potential. For Mercury vapor thyratrons, this time is around 1mili-second, and for hydrogen thyratrons this gets a lot lower. Only by removing the plate potential or reducing it to the point where the electrons do not have enough energy to produce ionization will tube conduction and the production of positive ions stop. Only after the production of positive ions is stopped will the grid be able to regain control.

Thyratron tubes are used typically in radar pulse modulators, particle accelerators, lasers, and high-voltage medical equipment.

Here is a Radar Modulator schematic, using a Hydrogen Thyratron:

More details available here.

It is also possible to use a Thyratron as an oscillator in a Tesla Coil:

This is only a test Thyratron Tesla coil device and needs further improvements. I used the following:
- high voltage DC supply (using a 100W flyback transformer, and a Royer push and pull oscillator), providing 8KV 10mA.
- rewound mot supply , for tube filament
- a ferrite choke for charging the PFN
- a pulse forming network, as presented here.
- a hydrogen thyratron, TGI2 400/16
- a 200V pulse generator, more details here.
The oscillator itself is described here.

Here is another Tesla coil switched by a Thyratron, actually this is the first design I've ever seen on the Internet. Mine would be the second :)
thyratron tesla coil
Construction details (in german) here.

Some pictures showing the beautiful 714 thyratron being energized:
pocketmagic.net thyratron tesla coil 1 pocketmagic.net thyratron tesla coil 2 pocketmagic.net thyratron tesla coil 3

pocketmagic.net thyratron tesla coil 4 pocketmagic.net thyratron tesla coil 5 pocketmagic.net thyratron tesla coil 6

(Visited 1,586 times, 3 visits today)
Tagged on:                         

22 thoughts on “Thyratrons

  • May 5, 2011 at 12:26 am

    Awesomeness! I want to do what you do, I play with electronics as a hobby and what you do is awesome! Please keep up the good work

  • May 5, 2011 at 10:38 am

    thanks Joey

  • July 10, 2011 at 9:00 am

    Domnule Radu un videoclip exceptional foarte bine realizat, cu ce program ati creat acest videoclip? Cum se numeste soundtrack-ul?

  • July 13, 2011 at 9:14 pm

    Multumesc , Robert!

  • October 21, 2011 at 11:00 pm

    Felicitari, domnule Radu! Ati facut o treaba foarte buna!

  • July 12, 2012 at 1:27 pm

    i want to know how 2d21 model thyratron works. actually it consists of two grids.i want to know how they function.

  • November 26, 2012 at 4:53 pm

    hello, i am impressed !! how beautiful is a thyratron working.
    I have a nixie clock, a tube amplifier and other “old fashioned” electronics, only for decorative purpose.
    I am thinking to make one thyratron “driver” for decorative purpose also, but is hard to find information about.
    ¿Do you think that is possible to make a design to maintain the thyratron working all the day without damaging it ?.
    I think that i must have a high DC source but a really low consumption, in the border of the thyratron shutdown.

  • November 27, 2012 at 10:19 am

    Yes, I think your idea would work!

  • November 27, 2012 at 10:41 am

    Ok !! i will try to make it, when i finished i will post here the result, i hope the result will be positive ;D

  • November 27, 2012 at 10:52 am

    Sounds good, looking forward to see it!

  • December 1, 2012 at 9:31 pm

    Do you know where I can get an older glass thyratron tube that was used in a modulator for an/GPS-20 type radar. These were about 12″ tall. Wanting for display only. I was a radar technician in the USAF and remember these getting turned into neat displays back-lit.

    Thanks. Andy

  • December 1, 2012 at 10:34 pm

    @Andy, wish I knew..

  • January 17, 2013 at 4:37 pm

    Am si eu o intrebare nevinovata…de unde ai facut rost de toate tuburile din colectia ta absolut fabuloasa? btw…genial videoclip, iti admir munca si tine-o tot asa.

  • January 17, 2013 at 5:54 pm

    Multumesc Alex. Tuburile tiratron prezentate aici, le-am prins pe ebay la un pret bun. Dar stii cum e, cand ai o anumita pasiune, strangi diverse lucruri care au legatura. Partea grea e sa le si folosim, ca timpul parca nu e niciodata destul.

  • Pingback: Tube: TGI2 400/16 (ТГИ2-400/16), Russian hydrogen thyratron « PocketMagic

  • July 8, 2013 at 12:51 am

    me gusta la electronica,para crear cosas raras para los demas que desconocen,

  • August 16, 2013 at 5:36 pm

    imi trimiti si mie schema te rog? e scumpa o lampa dinaia si produce radiatii nu?

  • August 18, 2013 at 1:28 pm

    @gabi, produce lumina si lumina e si ea o forma de radiatie electromagnetica.
    Dar probabil te referi la radiatie ionizanta ca si cea produsa in procesele nucleare. Aceste tuburi NU produc astfel de radiatii.

  • August 7, 2014 at 10:13 am

    Dear Sir/Madam
    We are pleased to send you an inquiry. Details are given below
    WT=1-KG‚ HEATER CURRENT 16.5 TO 23
    GRID STARTING V(2)=-30V TO -5
    DIA.90 MM‚H=350MM‚
    For High Frequency
    Model No. GP60-CR13-1 ZGI-6/15
    Qty: 14 Nos.
    Price is required on FOB as well as CFR Karachi, Pakistan
    If you have any queries, please feel free to contact us by e-mail or fax.
    Meanwhile, please acknowledge receipt of this inquiry and send your most
    Competitive offer URGENTLY by E-MAIL myl.unisonsintl@gmail.com

  • September 5, 2014 at 12:41 pm

    Dear Mr. Sir,
    Please quote for the following:
    PN: GP60-CR13-1 — Thyratron – high power electrical switch —25pcs
    Also, please send pictures.
    Best regards

  • January 27, 2015 at 11:19 pm

    How may I determine how may sieverts of ionizing radiation were likely emitted from an unshielded WWII pulsed radar supply?? Power supplies of this era employed two very large hydrogen filled triodes operating in tandem and gave off a bright blue glow when firing. How would this compare with an conventional x-ray device used in medicine??

  • January 27, 2015 at 11:30 pm

    @William if x-rays were indeed emitted, your best bet would probably be to take real time measurements on a similar setup or replica. Getting such data from calculations only seems complicated if not impossible.

Leave a Reply

Your email address will not be published. Required fields are marked *